PM-300

Heavy Duty Epoxy Coating

PRODUCT DESCRIPTION

PolyMax 300 Heavy Duty Epoxy Coating is a cycloaliphatic amine cured, pigmented high build epoxy, designed to be used where extra chemical, impact and abrasion resistance is required. Used primarily in heavy industrial and commercial applications, it can be applied with a glass smooth, high gloss finish or it can be combined with various aggregates to obtain virtually any level of slip resistance required.

This specially formulated epoxy exhibits excellent chemical, abrasion and impact resistance and excellent color retention. When properly installed at 8 to 16 mils, it will out wear normal floor paints up to 10 times

TYPICAL USE

Versatile PM-300 can be used as a heavy duty epoxy floor coating over concrete or steel, a finish coat for an epoxy mortar or broadcast overlay, or a primer/color coat for PolyMax Specialty Urethane finishes.

PM-300 epoxy coating is commonly installed in chemical processing areas, high traffic warehouses, loading docks, chemical laboratories, printing plants and machine shops.

Use PM-300 anywhere a top quality, chemical and abrasion resistant finish is required.

FEATURES

• Top Quality Formulation
• Economical Price - Longer Lasting
• Easy to use - 2 to 1 Mix Ratio
• Variety of Finishes
• Very Low VOC
• Fast Curing
• Very Good Chemical and Abrasion Resistance
• Good Impact Resistance
• Reduced Mixing Errors

INSTALLATION

The performance of any floor coating is highly reliant upon proper preparation of the substrate. Substrate must be free of all contamination such as latence, curing compounds, dirt, oil and or rust scale. Steel must be shot blasted to white metal. Concrete should be lightly shot blasted or acid etched and neutralized to a smooth, even finish similar in texture to 100 grit sand paper. Primers are necessary only when the substrate is porous. PM-300 epoxy develops adhesion properties stronger than concrete when substrate is properly prepared.

PM-300 epoxy coating is normally either rolled or squeegeed and back rolled. If a slip resistant finish is required, the appropriate aggregate can be pre-mixed with the A and B components or it may be broadcast on the surface once the coating has been applied. PM-300 can also sprayed. Contact Tele-Tech at 1-405-495-8848 for assistance and equipment suggestions.

PACKAGING

To maintain our top quality and low price, PM-300 is normally packaged in 5 gallon pails. 55 gallon drums and one gallon cans are also available with minimum quantity restrictions by special order.

STORAGE

For best shelf life, store PM-300 epoxy in a dry area at temperatures between 50 F and 90 F. Protect product from freezing. Minimum shelf life is one year from date of manufacture when properly stored.

LIMITATIONS

Avoid on or below grade applications where water vapor transmission is greater than 5 lbs./1000 sq. ft. per 24 hrs. or where ambient operating temperatures exceed 150 F or application temperatures below 40 F & above 90 F.

PM-300 EPOXY COATING is not designed for exterior use or constant exposure to direct sun light.

COMPLIANCES

PM-300 is compliant with the State of California Air Resources Board approved architectural coatings volatile organic compound (VOC) rule, San Diego APCD Rule 67, New York City AQMD Rule 205 and the New Jersey VOC requirements.

CHEMICAL RESISTANCE

PM-300 Epoxy is very resistant to most common industrial chemicals and solvents. An abbreviated list follows. For more comprehensive chemical resistance analysis, contact Tele-Tech at 1-800-495-8848.

NA = NO ATTACK D = DISCOLORED F = FAILED

Actual test results may vary due to the use of various aggregates, application methods and floor finish. The foregoing test results are based upon laboratory prepared samples and results may vary if not prepared by a professional technician.

AVAILABILITY

PolyMax products are available only through selected and approved applicators and distributors. This material is intended for commercial and industrial installations and should be installed by skilled, seamless flooring technicians. It is neither designed for nor available for consumer use.

Custom design assistance may be obtained by contacting PM Tele-Tech at 1-405-495-8848 8:00 AM through 4:00 PM Central time.

COLOR SELECTION

Standard colors are:

• Light Gray
• Brick Red
• Desert Tan

(Custom colors are available in 250 gallon minimums at additional charge)

CAUTION:

PM-300 Epoxy Coating Systems are intended for use by professional applicators. Although safe if properly handled, all personnel who are exposed to any chemical must read and completely understand precautions and warnings on label and MSDS prior to use.

COMPONENTS OF OR PRODUCTS USED WITH AND DURING THE INSTALLATION OF PolyMax COATINGS PRODUCTS MAY INCLUDE HAZARDOUS MATERIALS. All personnel exposed to or handling materials before and during installation must read and fully understand label precautions and Material Safety Data Sheets.

LIMITED WARRANTY

POLYMAX COATINGS are manufactured to meet the highest level of consistency and quality for their intended use. All PM300 materials are warranted to meet the physical properties as listed above. Should any POLYMAX COATING be proven to be defective within one year of the date of shipment, the material will be either replaced or at our discretion, a credit for the full purchase price will be issued. The successful performance of seamless flooring is highly dependent upon many factors beyond our control. Therefore, except for such replacement or refund POLYMAX and it's affiliates MAKE NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS, DESIGN COMPATIBILITY OR MERCHANTABILITY, RESPECTING ITS COATINGS. Other than that stated in the foregoing, POLYMAX and its affiliates shall have no other responsibility or liability, including direct and/or indirect and/or consequential damages and/or damages from delay and/or damages to any third party with respect to the use of it's materials. Claims regarding product quality must be received in writing within 30 days of discovery of defect.